About Joyetech ProCore Remix RTA/RDA/Subohm Atomizer
Joyetech is offering you electronic cigarette and e-liquid products too. They bring in a ton of VG and PG flavors too. Everything is easy to carry, and the company releases a plethora of e-cig kits for your convenience like Atopack Penguin, eVic VT, Primo and AIO, as well as Cuboid, UNIMAX and many others.
The procore is an atomizer series product that comes in a highly innovative system of top fill refills. The pro core SE is a glass tube in a full design that can be bottom filling or top filling with the controls. The vapor production here always delivers optimal flavor and the atomizer on board is perfect for the 2 ml reservoir. Pro core is a daily use product.
Product Instructions
Parameters
Tank: 2ml/ 4.5ml (exclude RDA)
Coil: Compatible with normal ProC series heads
Thread: 510 thread
Joyetech ProCore Remix RTA/RDA/Subohm Atomizer contains
- 1x ProCore Remix atomizer
- 1x Extended vent pipe
- 1x 2ml glass tube
- 1x RTA chamber
- 1x RDA chamber
- 1x RDA sleeve
- 1x RTA/RDA deck
- 1x ProC1 (0.4ohm) head
- 1x Pure cotton
- 2x Clapton coil
- 1x Quick start
- 1x Warranty card
- 1x Warning card
- Spare parts
Simple packing. Customary Packing from the factory, the packing is subject to change without notice.
- Empty tank. You need buy liquid to work with it.
- You can buy replacement ProC1/ProC1-S/ProC2/ProC3/ProC4 heads.
- 510 thread
Features
One kit variable for four atomizers - RTA/RDA/4.5ml Subohm/ 2ml Subohm
Firstly introduced Joye RTA/RDA
Easily transform to sub-ohm atomizers
Single or dual coil rebuild for option
Intense cloud and flavor chasing combo
Compatible with normal ProC series heads
Flip type top-fill design
Operation Guide
A: Using as an RTA
1. Break down the atomizer and loosen the screws with the hex wrench.
2. Place the first coil into the post holes.
3. Secure the coil in place and blend the excess wire outwards.
4. Do the same with the second coil on the other side. (You can also choose to use single coil with the stopper.)
5. Tighten down the screws and make sure they're nicely secured.
6. Snip off the excess wire.
7. Straighten out the coils and make sure they're not touching the deck.
8. Attach the atomizer base into your battery mod and press the fire button to heat the coil up to red. (Please wait until it cools down to avoid scorching. )
9. After the coil cools down, tear down a piece of pure cotton and place it into the coil carefully.
10. Trim the cotton tight to the deck and push it back inside.
11. Drip a few drops of e-liquids into the cotton to get it fully soaked and left it sit for a while.
12. Install the chamber and screw the atomizer base back on.
B: Using as an RDA
1. Break down the atomizer and loosen the screws with the hex wrench.
2. Place the first coil into the post holes.
3. Secure the coil in place and blend the excess wire outwards.
4. Do the same with the second coil on the other side. (You can also choose to use single coil with the stopper.)
5. Tighten down the screws and make sure they're nicely secured.
6. Snip off the excess wire.
7. Straighten out the coils and make sure they're not touching the deck.
8. Attach the atomizer base into your battery mod and press the fire button to heat the coil up to red. (Please wait until it cools down to avoid scorching. )
9. After the coil cools down, tear down a piece of pure cotton and place it into the coil carefully.
10. Trim the cotton tight to the deck and push it back inside.
11. Drip a few drops of e-liquids into the cotton to get it fully soaked and left it sit for a while.
12. Put three O-rings into the grooves on the RDA sleeve separately.
13. Install the RDA Sleeve and put the RDA chamber back on.
C: Using as a sub-ohm atomizer (standard)
1. Break down the atomizer, unscrew the RDA/RTA deck and replace with the ProC head.
2. Drip a few drops of e-liquid into the head.
3. Screw the extended vent pipe onto the top cap.
4. Put the standard glass tube on and install the whole atomizer.
D: Using as a sub-ohm atomizer (2ml)
1. Break down the atomizer, unscrew the RDA/RTA deck and replace with the ProC head.
2. Drip a few drops of e-liquid into the head.
3. Put the 2ml glass tube on and install the whole atomizer.
E-liquid filling for sub-ohm atomizers:
1. Aimed at the sign on top, push and pull the top cap to reveal the filling holes.
2. Inject the e-liquid into the holes on both sides and close the top cap.
3. Rotate the bottom airflow and inhale for a few times without pressing the fire button.
4. Press the fire button and enjoy the flavor.
